Zyxel-communications Omni 288S Manual do Utilizador Página 71
- Página / 136
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 9 - Fax Operation
9-9
Command Value Description
disabled.
tq=1 DCE Transmit Copy Quality Checking
enabled.
tq=2 DCE Transmit Copy Quality Correction
enabled.
+FCR=n "Capability to receive" parameter
n=0 DCE will not receive message or poll a
remote device.
n=1 DCE receives message data or polls a remote
device
+FCT=n 0-255 DTE phase C time-out parameter. n=0-255, 1
units.
+FDR Receive phase C data command initiates
document reception
+FDT Transmit phase C data command: releases the
DCE to proceed with negotiation
+FEA=n Phase C received EOL alignment parameter
n=0 Determine that T.4 EOL patterns are bit aligned
(as received).
n=1 Determine that the last received bits of T.4
EOL patterns are byte aligned by the DCE, with
necessary zero fill bits inserted.
+FIE=n Procedure interrupt parameter
n=0 Procedure interrupt requests from the remote
station are ignored, and not reported to the
DTE.
n=1 Procedure interrupt requests from the remote
station are accepted, negotiated and reported
using the +FVO response.
+FIP Initialize facsimile parameters to factory
default.
+FIS=vr,br,wd,ln,
df,ec,bf,st
Current session parameter. refer to +FDCC Class
2 command in previous section parameter settings.
+FKS Session termination command.
+FLI="string" Local ID string parameter.
+FLO=n Flow control options:
n=0 No flow control.
n=1 Set XON/XOFF software flow control.
n=2 Set CTS/RTS hardware flow control.
+FLP=n Document for polling command:
n=0 The DTE has no document for polling.
n=1 Indicated document available for polling.
- Omni 288S 1
- User’s Manual 1
- Limited Warranty 2
- Copyright 1996 by ZyXEL 2
- Acknowledgements 2
- FCC Part 15 Information 3
- FCC Requirements 3
- Table of Contents 6
- Chapter 1 - Introduction 11
- Unpacking Your Modem 12
- Becoming a Registered Owner 13
- Omni 288S Modem Features 13
- Intelligent Features 14
- Fax Compatibility 14
- Voice Features 14
- Technical Specifications 15
- Chapter 2 - Installation 16
- Telephone Jack 17
- Microphone 17
- Windows 95 Dial-up Networking 20
- Understanding AT Commands 26
- Dialing using the ATD Command 27
- Making Your First Connection 28
- Modem Result Codes 30
- Viewing S Register Values 30
- Non-Volatile Memory 31
- Mac Serial Port 33
- Mac Software Tips 33
- Serial Cable 34
- Basic Modem Settings for UNIX 34
- Unix Software Tips 34
- Front Panel LEDs 35
- DTE Interface 36
- RS-232C or EIA-232D/E 37
- Serial RS-232C Cable 37
- Error Control 39
- Data Compression 40
- Run Length Encoding 41
- Adaptive Frequency Encoding 41
- String Coding 41
- Hardware CTS/RTS 42
- Software XON/XOFF 42
- V.25bis Command Set 43
- Clock Options 44
- RTS Options 44
- Command State Options 44
- Dialing from Synchronous Mode 45
- Leased Line Handshaking 46
- Manual Connect 47
- Auto Handshake 47
- Cellular Phone Systems 48
- Cellular Impairments 48
- ZyCellular Modes 49
- Cellular Mode Usage 50
- Office Installation 53
- Security Functions 54
- Remote Configuration 55
- Distinctive Ring 59
- Setting Up EDR 61
- EDR Application Example 62
- Chapter 9 - Fax Operation 63
- Fax Command sets 64
- Class 1 Command Set 65
- Class 2 Command Set 66
- Class 2.0 Command Set 70
- Extended Fax AT Command Set 75
- Fax Reception from a BBS 78
- Set external mail as: 79
- Voice Data Compression 80
- Voice Input/Output Devices 81
- Recording a greeting message 82
- Voice Command State 85
- Voice Data States 86
- Voice Data Reception State 86
- Event Detection and Reporting 87
- Voice AT Commands 89
- AT Command Syntax 90
- Response Syntax 90
- Flow Control 90
- ATD (with +FCLASS=8) 91
- ATH (with + FCLASS=8) 91
- AT+FCLASS=<mode> 91
- Voice Mode Action Commands 93
- AT+VTS=<string> 94
- AT+VTS=? 94
- AT+VTX 94
- AT+VGR=<gain> 95
- AT+VGR? 95
- AT+VGR=? 95
- AT+VGT=<level> 95
- AT+VLS? 97
- AT+VLS=? 97
- AT+VSD? 97
- AT+VSD=? 97
- Basic AT Command Set 99
- Description of ATI2 Output: 101
- Extended AT& Command Set 102
- Extended AT* Command Set 105
- S-Register Descriptions 107
- Result Code Options 116
- Diagnostics 118
- Resetting The Modem 119
- Loopback Tests 119
- Indicator Lights 120
- Trouble Shooting 121
- Command Echo Problems 122
- Answer Problems 123
- Dialing Problems 123
- Data Transfer Problems 123
- Connect Problems 124
- Upgrading by Flash EPROM 125
- Kernel Recovery Mode 125
- ZyXEL Phone Numbers 126
- Online Access 127
- Phone Jack Pinouts 128
- PC Serial Port Pinouts 128
- Macintosh Serial Port Pinouts 129
- Glossary 130
Manuais e produtos relacionados com Hardware Zyxel-communications Omni 288S
(133 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais