ZyXEL Communications ES-3024 Guia do Utilizador Página 42
- Página / 212
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Dimension ES-3024 Ethernet Switch
3-8 Hardware Connections
Figure 3-10 Uplink Example
3.8 Configuring the ES-3024
You may use the embedded web configurator or command line interface to configure the ES-3024. If you’re using
the web configurator, you need Internet Explorer 5.5 and later or Netscape Navigator 6 and later.
You can access the command line interface using a terminal emulation program on a computer connected to the
switch console port (see section 3.2.1) or access the switch via an Ethernet port using Telnet.
You can use the “config save” command to save 802.1Q, STP, Cluster and IP configuration
changes to non-volatile memory (Flash). These changes are effective after you restart the switch.
However you cannot use “config save” for all other line command configurations. These are
saved in volatile memory (DRAM), so are not effective after you restart the switch.
The next part of this guide discusses configuring the ES-3024 using the web configurator.
- Dimension 1
- ES-3024 1
- Copyright 2
- ZyXEL Limited Warranty 3
- Customer Support 5
- Table of Contents 6
- List of Figures 11
- List of Charts 14
- List of Tables 15
- List of Tables xvii 17
- Preface 18
- User Guide Feedback 19
- Features And Applications 20
- Chapter 1 22
- to Know the ES-3024 22
- 1.1.2 Firmware Features 23
- 1.2 Applications 24
- 1.2.2 Bridging Example 25
- VLAN Shared Server Example 28
- Part II 30
- Chapter 2 31
- Hardware 31
- Installation 31
- Hardware Installation 2-3 33
- Chapter 3 35
- Connections 35
- 3.3 Uplink Modules 36
- Slide the optional module 37
- 3.4 Rear Panel 38
- 3.5 Front Panel LEDs 38
- 3.7 Uplink Scenario Example 41
- 3.8 Configuring the ES-3024 42
- Getting Started 43
- Chapter 4 45
- Introducing 45
- the Web Configurator 45
- Maintenance 47
- 4.4 Switch Lockout 49
- 4.5 Resetting the Switch 50
- 4.5.2 Help 51
- Chapter 5 53
- Status and Port Details 53
- 5.2.1 Port Details 54
- LABEL DESCRIPTION 58
- Chapter 6 59
- Setting 59
- 6.3 General Setup 61
- 6.4 Introduction to VLANs 63
- 6.5 IGMP Snooping 64
- 6.6 Switch Setup Screen 64
- 6-8 Basic Setting 66
- Table 6-3 Switch Setup 66
- 6.7 IP Setup 67
- 6.8 Port Setup 68
- Basic Setting 6-11 69
- Figure 6-4 Port Setup 69
- 6-12 Basic Setting 70
- Table 6-5 Port Setup 70
- Advanced Application 1 71
- Chapter 7 72
- GARP Timers 73
- 7.2 802.1Q VLAN 74
- 7.2.2 802.1Q Static VLAN 77
- VLAN 7-7 78
- VID1 Example Screen 80
- VLAN 7-11 82
- 7-12 VLAN 83
- Chapter 8 86
- MAC Forward Setup 86
- Chapter 9 88
- 9-4 Filtering 91
- Chapter 10 92
- Spanning 92
- Tree Protocol 92
- 10.2 STP Status 93
- 10.2.1 Configuring STP 95
- Spanning Tree Protocol 10-5 96
- Chapter 11 98
- Bandwidth 98
- 11-4 Bandwidth Control 101
- Advanced Application 2 102
- Chapter 12 104
- Broadcast 104
- Storm Control 104
- Chapter 13 108
- Mirroring 108
- Chapter 14 112
- Aggregation 112
- 14.1.2 Link Aggregation ID 113
- Link Aggregation 14-5 116
- Chapter 15 118
- Authentication 118
- Port Authentication 15-3 120
- Chapter 16 122
- Security 122
- Port Security 16-3 124
- Table 16-1 Port Security 124
- Port Security 16-1 126
- Chapter 17 128
- Control 128
- 17.3 About SNMP 129
- 17.3.1 Supported MIBs 130
- 17.3.2 SNMP Traps 130
- 17.3.3 Configuring SNMP 130
- 17.5 Remote Management 133
- Chapter 18 136
- Method 136
- 18-2 Queuing Method 137
- Figure 18-1 Queuing Method 137
- Queuing Method 18-3 138
- Table 18-2 Queuing Method 138
- Part VI 139
- Chapter 19 140
- Protocol 140
- Routing Protocol 19-3 142
- Chapter 20 144
- Maintenance 144
- Step 1. Click Backup 145
- 20.5 Load Factory Defaults 146
- 20.6 Reboot System 146
- 20.7 Command Line FTP 147
- 20.7.3 GUI-based FTP Clients 148
- Chapter 21 150
- Diagnostic 150
- 21-2 Diagnostic 151
- Table 21-1 Diagnostic 151
- Chapter 22 152
- Management 152
- Cluster Manager 154
- Cluster Member 154
- Cluster Management 22-5 156
- 22-6 Cluster Management 157
- Chapter 23 158
- Filtering 158
- Database 158
- Filtering Database 23-3 160
- Chapter 24 162
- Commands 164
- Chapter 25 166
- Introduction 166
- to CLI 166
- 25.2 Command Summary 167
- 25.2.2 sys sw Commands 172
- Introduction to CLI 25-9 174
- 25-10 Introduction to CLI 175
- Introduction to CLI 25-11 176
- 25-12 Introduction to CLI 177
- Introduction to CLI 25-13 178
- 25.2.3 exit Command 179
- 25.2.4 ip Commands 180
- 25.2.5 config Command 181
- Introduction to CLI 25-17 182
- Chapter 26 184
- Examples 184
- 26.2.3 sys version 185
- 26.2.4 sys monitor status 185
- 26.2.6 sys ixe2424 pktcnt 186
- 26.3 sys cluster Commands 187
- 26.4 ip Commands 189
- 26.4.4 ip dhcp Commands 190
- Chapter 27 192
- 802.1Q Tagged VLAN Commands 192
- 27.4.1 garp status 194
- 27.4.2 garp timer 194
- 27.4.3 gvrp status 195
- 27.4.4 gvrp enable 195
- 27.4.5 gvrp disable 195
- 27.4.6 vlan1q port status 196
- 27.4.8 vlan1q port accept 196
- 27.4.10 vlan1q svlan cpu 197
- 27.4.9 vlan1q port gvrp 197
- Forwarding Process Example 198
- 27.5 vlan1q svlan active 199
- 27.6 vlan1q svlan inactive 199
- 27.7 vlan1q svlan list 199
- 27.8 vlan1q vlan list 200
- Appendices and Index 202
- A Product Specifications 203
- A-2 Product Specifications 204
- B Index 207
Manuais e produtos relacionados com Redes ZyXEL Communications ES-3024
Redes ZyXEL Communications V300 Guia do Utilizador
(43 páginas)
(43 páginas)
Redes ZyXEL Communications GS-4012F Guia do Utilizador
(144 páginas)
(144 páginas)
Redes ZyXEL Communications G-5100 Guia do Utilizador
(13 páginas)
(13 páginas)
(30 páginas)
(4 páginas)
(2 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais