ZyXEL Communications MES-2110 Guia do Utilizador Página 1

www.zyxel.comwww.zyxel.comMES-2110Intelligent Layer 2 SwitchCopyright © 2009 ZyXEL Communications CorporationFirmware Version 1.00Edition 2, 9/2009Def

Contents OverviewMES-2110 User’s Guide10

Chapter 14 Port MirroringMES-2110 User’s Guide100The following table describes the labels in this screen. Table 39 Configuration > Port Mirroring

MES-2110 User’s Guide101CHAPTER 15 Link Aggregation15.1 Overview Link aggregation (trunking) is the grouping of physical ports into one logical high

Chapter 15 Link AggregationMES-2110 User’s Guide102• You must connect all ports point-to-point to the same Ethernet switch and configure the ports for

Chapter 15 Link AggregationMES-2110 User’s Guide1032 Configure static trunking-Click Configuration > Trunk Config > Aggregator Setting. In this

Chapter 15 Link AggregationMES-2110 User’s Guide104The following table describes the labels in this screen.15.5 Link Aggregation Control Protocol C

Chapter 15 Link AggregationMES-2110 User’s Guide10515.6 LACP Link Status Click Configuration > Trunk Config > LACP Link Status in the navigati

Chapter 15 Link AggregationMES-2110 User’s Guide106

MES-2110 User’s Guide107CHAPTER 16 IGMP16.1 Overview Traditionally, IP frames are transmitted in one of either two ways - Unicast (1 sender to 1 rec

Chapter 16 IGMPMES-2110 User’s Guide10816.1.3 IGMP Snooping and VLANsThe Switch can perform IGMP snooping on up to 16 VLANs. You can configure the Sw

Chapter 16 IGMPMES-2110 User’s Guide109The following table describes the labels in this screen. Table 45 Configuration > IGMP Menu > IGMP Con

Table of ContentsMES-2110 User’s Guide11Table of ContentsAbout This User's Guide ...

Chapter 16 IGMPMES-2110 User’s Guide11016.3 IGMP Status Click Configuration > IGMP Menu > IGMP Group Status to display the screen as shown. Thi

Chapter 16 IGMPMES-2110 User’s Guide111The following figure shows a network example. The subscriber VLAN (1, 2 and 3) information is hidden from the

Chapter 16 IGMPMES-2110 User’s Guide112When the subscriber changes the channel or turns off the computer, an IGMP leave message is sent to the Switch

Chapter 16 IGMPMES-2110 User’s Guide113Note: Your Switch automatically creates a static VLAN (with the same VID) when you create a multicast VLAN in

Chapter 16 IGMPMES-2110 User’s Guide11416.6 MVR Group Configuration All source ports and receiver ports belonging to a multicast group can receive mu

Chapter 16 IGMPMES-2110 User’s Guide115Note: A port can belong to more than one multicast VLAN. However, IP multicast group addresses in different mu

Chapter 16 IGMPMES-2110 User’s Guide11616.6.1 MVR Configuration ExampleThe following figure shows a network example where ports 1, 2 and 3 on the Swi

Chapter 16 IGMPMES-2110 User’s Guide117To configure the MVR settings on the Switch, create a multicast group in the MVR screen and set the receiver a

Chapter 16 IGMPMES-2110 User’s Guide118following figure shows an example where two multicast groups (Group ID 1 for News and Group ID 2 for Movie) are

MES-2110 User’s Guide119CHAPTER 17 IP Source Guard17.1 OverviewIP source guard uses a binding table to distinguish between authorized and unauthoriz

Table of ContentsMES-2110 User’s Guide123.1.4 Power Connector ...

Chapter 17 IP Source GuardMES-2110 User’s Guide12017.1.1.1 Trusted vs. Untrusted PortsEvery port is either a trusted port or an untrusted port for DH

Chapter 17 IP Source GuardMES-2110 User’s Guide12117.2 DHCP Snooping ConfigurationUse this screen to enable DHCP snooping on the Switch and specify

Chapter 17 IP Source GuardMES-2110 User’s Guide122DHCP Snooping OptionSelect Enable to have the Switch add DHCP relay agent option 82 information to D

Chapter 17 IP Source GuardMES-2110 User’s Guide12317.3 DHCP Binding TableBindings are used by DHCP snooping and ARP inspection to distinguish betwee

Chapter 17 IP Source GuardMES-2110 User’s Guide12417.4 The ARP Inspection ScreenUse ARP inspection to filter unauthorized ARP frames on the network.

Chapter 17 IP Source GuardMES-2110 User’s Guide12517.4.1 Configuring ARP InspectionFollow these steps to configure ARP inspection on the Switch.1 Co

Chapter 17 IP Source GuardMES-2110 User’s Guide126ARP Inspection VLAN (Fixed)Enter the ID of a static VLAN; the valid range is between 1 and 4094.Acti

MES-2110 User’s Guide127CHAPTER 18 MAC18.1 OverviewThe MAC Table screen (a MAC table is also known as a filtering database) shows how frames are for

Chapter 18 MACMES-2110 User’s Guide128• If the Switch has already learned the port for this MAC address, but the destination port is the same as the p

Chapter 18 MACMES-2110 User’s Guide12918.3 The Lock MAC Address Learning ScreenUse this screen to configure the MAC address learning settings. Click

Table of ContentsMES-2110 User’s Guide138.2 The Jumbo Frame Configuration Screen ...

Chapter 18 MACMES-2110 User’s Guide130The following table describes the labels in this screen. 18.4 The MAC Filter Configuration ScreenUse this scree

Chapter 18 MACMES-2110 User’s Guide131Pri-Override Use this to ignore the priority level assigned to the transmitted frames.MAC Address Type a MAC ad

Chapter 18 MACMES-2110 User’s Guide13218.4.1 The MAC Filter Mode ScreenUse this screen to configure the MAC filter setting on each port. In the Confi

Chapter 18 MACMES-2110 User’s Guide13318.5 The MAC Limit Configuration ScreenUse this screen to limit the number of MAC addresses that can be learne

Chapter 18 MACMES-2110 User’s Guide134

MES-2110 User’s Guide135CHAPTER 19 QoS19.1 OverviewQuality of Service (QoS) is used to prioritize source-to-destination traffic flows. All frames in

Chapter 19 QoSMES-2110 User’s Guide136handle. Queues with larger weights get more service than queues with smaller weights. This queuing mechanism is

Chapter 19 QoSMES-2110 User’s Guide137Priority Mode Select a priority mode for the port.802.1p Priority uses port priority as queuing basis. Assign a

Chapter 19 QoSMES-2110 User’s Guide13819.3 The 802.1p Priority TableUse this screen to assign a priority level for each port. Click Configuration >

Chapter 19 QoSMES-2110 User’s Guide13919.4 The Tag Priority TableClick Configuration > QoS Menu > Tag Priority to open the following screen.Fi

Table of ContentsMES-2110 User’s Guide1411.5.9 The Management VLAN Screen ...

Chapter 19 QoSMES-2110 User’s Guide140Use this to assign DSCP priority settings. Click Configuration > QoS Menu > IP DSCP Priority to open the f

Chapter 19 QoSMES-2110 User’s Guide141Click Configuration > QoS Menu > Priority Override Configuration to open the following screen.Figure 77

Chapter 19 QoSMES-2110 User’s Guide142

143PART IVManagementMgmt Config and System Restart Menu (145)

144

MES-2110 User’s Guide145CHAPTER 20 Mgmt Config and SystemRestart Menu20.1 OverviewThis chapter explains how to configure the screens that let you ma

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide14620.3 The SNMP Configuration ScreensSimple Network Management Protocol (SNMP) is

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide147SNMP itself is a simple request/response protocol based on the manager/agent mo

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide148managers. Use this screen to configure the trap manager settings. Click Mgmt Con

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide149The following table describes the labels in this screen. Table 65 Mgmt Config

Table of ContentsMES-2110 User’s Guide15Chapter 17IP Source Guard...

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide15020.5 Alarms and LogsUse this screen to configure the mail server, the syslog an

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide15120.6 The User Configuration ScreenUse this screen to configure user names, pas

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide15220.7 The Cable Test ScreenUse this feature to diagnose the connection on each p

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide15320.8 The Host DoS ProtectionYou can specify a group of one or more “trusted co

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide15420.9 The Port Abnormal Traffic Detection ScreenThis Switch can detect excessive

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide15520.10 Upgrading the FirmwareMake sure you have downloaded (and unzipped) the c

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide156Type the path and file name of the firmware file you wish to upload to the Switc

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide157restart the system without physically turning the power off. It also allows you

Chapter 20 Mgmt Config and System Restart MenuMES-2110 User’s Guide158

159PART VTroubleshooting & Product SpecificationsTroubleshooting (161)Product Specifications (165)

Table of ContentsMES-2110 User’s Guide1620.8 The Host DoS Protection ...

160

MES-2110 User’s Guide161CHAPTER 21 TroubleshootingThis chapter offers some suggestions to solve problems you might encounter. The potential problems

Chapter 21 TroubleshootingMES-2110 User’s Guide1621 Make sure you understand the normal behavior of the LED. See Section 3.2 on page 34.2 Check the ha

Chapter 21 TroubleshootingMES-2110 User’s Guide163• If you changed the IP address and have forgotten it, see the troubleshooting suggestions for I fo

Chapter 21 TroubleshootingMES-2110 User’s Guide164In order to use the web configurator you need to allow:• Web browser pop-up windows from your device

MES-2110 User’s Guide165CHAPTER 22 Product SpecificationsThe following tables summarize the Switch’s hardware and firmware features.Table 71 Hardwa

Chapter 22 Product SpecificationsMES-2110 User’s Guide166Table 72 Firmware Specifications FEATURE DESCRIPTIONDefault IP Address 192.168.1.1Default S

Chapter 22 Product SpecificationsMES-2110 User’s Guide167Multicast VLAN Registration (MVR)Multicast VLAN Registration (MVR) is designed for applicati

Chapter 22 Product SpecificationsMES-2110 User’s Guide168The following list, which is not exhaustive, illustrates the standards supported in the Switc

169PART VIAppendices and IndexChanging a Fuse (171)Common Services (173)Legal Information (177)Index (181)

17PART IIntroduction and HardwareGetting to Know Your Switch (19)Hardware Installation and Connection (25)Hardware Overview (29)

170

MES-2110 User’s Guide171APPENDIX A Changing a FuseThis appendix shows you how to remove and install fuses for the Switch.If you use a fuse other than

Appendix A Changing a FuseMES-2110 User’s Guide172

MES-2110 User’s Guide173APPENDIX B Common ServicesThe following table lists some commonly-used services and their associated protocols and port numbe

Appendix B Common ServicesMES-2110 User’s Guide174Table 74 Commonly Used ServicesNAME PROTOCOL PORT(S) DESCRIPTIONAH (IPSEC_TUNNEL)User-Defined 51 T

Appendix B Common ServicesMES-2110 User’s Guide175NEW-ICQ TCP 5190 An Internet chat program.NEWS TCP 144 A protocol for news groups.NFS UDP 2049 Net

Appendix B Common ServicesMES-2110 User’s Guide176SQL-NET TCP 1521 Structured Query Language is an interface to access data on many different types of

MES-2110 User’s Guide177APPENDIX C Legal InformationCopyrightCopyright © 2009 by ZyXEL Communications Corporation.The contents of this publication ma

Appendix C Legal InformationMES-2110 User’s Guide178• This device must accept any interference received, including interference that may cause undesir

Appendix C Legal InformationMES-2110 User’s Guide179Viewing Certifications1 Go to http://www.zyxel.com.2 Select your product on the ZyXEL home page t

18

Appendix C Legal InformationMES-2110 User’s Guide180

IndexMES-2110 User’s Guide181IndexAabnormal traffic detection 154accounts 151alarms 150applicationbackbone 19bridging 20metropolitan 22trunking 21VLAN

IndexMES-2110 User’s Guide182GGigabit Ethernet ports 30Hhardwareconsole port 30front panel 29Gigabit Ethernet ports 30installation 25LEDs 34mini-GBIC

IndexMES-2110 User’s Guide183navigation panel 40Ppassword 44path cost 75, 79port authenticationand RADIUS 71port configuration 53port mirroring 99port

IndexMES-2110 User’s Guide184Uunicast 107user accounts 151VVLAN 83application 21configuration 85forwarding frames 84frame formats 90management VLAN 94

MES-2110 User’s Guide19CHAPTER 1 Getting to Know Your Switch1.1 IntroductionThis chapter introduces the main features and applications of the Switch

Chapter 1 Getting to Know Your SwitchMES-2110 User’s Guide20In this example, all computers can share high-speed applications on the server. To expand

Chapter 1 Getting to Know Your SwitchMES-2110 User’s Guide211.1.3 High Performance Switching ExampleThe Switch is ideal for connecting two networks

Chapter 1 Getting to Know Your SwitchMES-2110 User’s Guide22Shared resources such as a server can be used by all ports in the same VLAN as the server.

Chapter 1 Getting to Know Your SwitchMES-2110 User’s Guide23possible. The Switch is connected to the backbone and the metropolitan servers over an op

Chapter 1 Getting to Know Your SwitchMES-2110 User’s Guide24• Change the password. Use a password that’s not easy to guess and that consists of differ

MES-2110 User’s Guide25CHAPTER 2 Hardware Installation andConnection2.1 Installation ScenariosThis chapter shows you how to install and connect the

Chapter 2 Hardware Installation and ConnectionMES-2110 User’s Guide265 Attach the rubber feet to each corner on the bottom of the Switch. These rubber

Chapter 2 Hardware Installation and ConnectionMES-2110 User’s Guide272.3.1.1 Precautions • Make sure the rack will safely support the combined weigh

Chapter 2 Hardware Installation and ConnectionMES-2110 User’s Guide282.3.3 Mounting the Switch on a Rack1 Position a mounting bracket (that is alread

MES-2110 User’s Guide29CHAPTER 3 Hardware OverviewThis chapter describes the front panel and rear panel of the Switch and shows you how to make the h

About This User's GuideMES-2110 User’s Guide3About This User's GuideIntended AudienceThis manual is intended for people who want to config

Chapter 3 Hardware OverviewMES-2110 User’s Guide303.1.1 Console PortFor local management, you can use a computer with terminal emulation software con

Chapter 3 Hardware OverviewMES-2110 User’s Guide31When auto-negotiation is turned on, a Ethernet port negotiates with the peer automatically to deter

Chapter 3 Hardware OverviewMES-2110 User’s Guide323.1.3.1 Transceiver Installation Use the following steps to install a mini-GBIC transceiver (SFP mo

Chapter 3 Hardware OverviewMES-2110 User’s Guide333 Pull the transceiver out of the slot.Figure 12 Removing the Fiber Optic Cables Figure 13 Open

Chapter 3 Hardware OverviewMES-2110 User’s Guide343.2 LEDs After you connect the power to the Switch, view the LEDs to ensure proper functioning of t

35PART IIBasic ConfigurationThe Web Configurator (37)System Details (47)

36

MES-2110 User’s Guide37CHAPTER 4 The Web Configurator4.1 IntroductionThis section introduces the configuration and functions of the web configurator

Chapter 4 The Web ConfiguratorMES-2110 User’s Guide383 The login screen appears. Enter the user name (admin by default) and password (1234 by default)

Chapter 4 The Web ConfiguratorMES-2110 User’s Guide394.3 The Main Screen The Main screen is the first screen that displays when you access the w

About This User's GuideMES-2110 User’s Guide4• Download LibrarySearch for the latest product updates and documentation from this link. Read the T

Chapter 4 The Web ConfiguratorMES-2110 User’s Guide40In the navigation panel, click a main link to reveal a list of submenu links.Table 3 Navigation

Chapter 4 The Web ConfiguratorMES-2110 User’s Guide41The following table lists the various web configurator screens within the sub-links. Table 4 W

Chapter 4 The Web ConfiguratorMES-2110 User’s Guide42The following table describes the links in the navigation panel. DHCP SnoopingDHCP Snooping Confi

Chapter 4 The Web ConfiguratorMES-2110 User’s Guide43Bandwidth ControlThis link takes you to a screen where you can configure bandwidth limits on the

Chapter 4 The Web ConfiguratorMES-2110 User’s Guide444.3.1 Set Up the Administrative Password After you log in for the first time, it is recommende

Chapter 4 The Web ConfiguratorMES-2110 User’s Guide454.5 Switch Lockout You could block yourself (and all others) from using in-band-management (m

Chapter 4 The Web ConfiguratorMES-2110 User’s Guide462 Disconnect and reconnect the Switch’s power to begin a session. When you reconnect the Switch’s

MES-2110 User’s Guide47CHAPTER 5 System Details5.1 OverviewThe System Details screens show general system information about the Switch. You can also

Chapter 5 System DetailsMES-2110 User’s Guide48The following table describes the labels in this screen.5.3 The Board Information ScreenUse this scree

Chapter 5 System DetailsMES-2110 User’s Guide49The following table describes the labels in this screen.5.4 The DHCP Configuration ScreenUse this scr

Document ConventionsMES-2110 User’s Guide5Document ConventionsWarnings and NotesThese are how warnings and notes are shown in this User’s Guide. Warn

Chapter 5 System DetailsMES-2110 User’s Guide50Once you click the Apply button, the following message displays, reminding you to save your settings in

51PART IIIConfigurationConfiguration (53)Loop Detection (59)Bridge (75)VLAN (83)Bandwidth Control (95)Broadcast Storm Control (97)Port Mirroring

52

MES-2110 User’s Guide53CHAPTER 6 Configuration6.1 OverviewThe Configuration screens let you configure the Switch settings.6.2 The Port Configuratio

Chapter 6 ConfigurationMES-2110 User’s Guide54The following table describes the labels in this screen. Table 9 Configuration > Port Configuration

Chapter 6 ConfigurationMES-2110 User’s Guide556.3 The Port Status Screen To view the port statistics, click Configuration > Port Status to dis

Chapter 6 ConfigurationMES-2110 User’s Guide56The following table describes the labels in this screen. Table 10 Configuration > Port Status LABEL

Chapter 6 ConfigurationMES-2110 User’s Guide576.4 The RMON Status Screen Use this screen to view individual port statistics. Click Configuration >

Chapter 6 ConfigurationMES-2110 User’s Guide58InBadOctets This field shows the number of bad octet frames received.InUndersize This field shows the nu

MES-2110 User’s Guide59CHAPTER 7 Loop Detection7.1 OverviewLoop detection allows you to configure the Switch to shut down a port if it detects that

Document ConventionsMES-2110 User’s Guide6Icons Used in FiguresFigures in this User’s Guide may use the following generic icons. The Switch icon is no

Chapter 7 Loop DetectionMES-2110 User’s Guide60The following figure shows a loop detection enabled port N on switch A sending a probe frame P to switc

Chapter 7 Loop DetectionMES-2110 User’s Guide61The following table describes the labels in this screen. Table 12 Configuration > Loop DetectionL

Chapter 7 Loop DetectionMES-2110 User’s Guide62

MES-2110 User’s Guide63CHAPTER 8 Jumbo Frame8.1 OverviewJumbo frames are Ethernet frames with a payload greater than 1500 bytes. Jumbo frames can en

Chapter 8 Jumbo FrameMES-2110 User’s Guide64

MES-2110 User’s Guide65CHAPTER 9 802.1x9.1 Overview This chapter describes the IEEE 802.1x authentication method. Port authentication is a way to va

Chapter 9 802.1xMES-2110 User’s Guide66request to a RADIUS server. The RADIUS server validates whether this client is allowed access to the port. Fi

Chapter 9 802.1xMES-2110 User’s Guide679.2 802.1x Global Configuration Screen Use this screen to enable port authentication and a guest VLAN on the

Chapter 9 802.1xMES-2110 User’s Guide68Click Configuration > 802.1x > Radius Server Configuration in the navigation panel to display the screen

Chapter 9 802.1xMES-2110 User’s Guide69Click Configuration > 802.1x > Port Configuration in the navigation panel to display the screen as shown

Safety WarningsMES-2110 User’s Guide7Safety Warnings• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.• Do

Chapter 9 802.1xMES-2110 User’s Guide709.5 802.1x Radius Server Configuration Screen Use this screen to view a summary of port authentication setting

Chapter 9 802.1xMES-2110 User’s Guide719.6 Technical ReferenceThis section provides technical background information about the topics covered in thi

Chapter 9 802.1xMES-2110 User’s Guide72Refer to RFC 2865 for more information about RADIUS attributes used for authentication. Refer to RFC 2866 and R

Chapter 9 802.1xMES-2110 User’s Guide739.6.4 Attributes Used for AccountingThe following sections list the attributes sent from the Switch to the RA

Chapter 9 802.1xMES-2110 User’s Guide749.6.4.3 Attributes Used for Accounting IEEE 802.1x Events The attributes are listed in the following table alo

MES-2110 User’s Guide75CHAPTER 10 Bridge10.1 OverviewThe Switch supports Rapid Spanning Tree Protocol (RSTP) as defined in the IEEE 802.1w Rapid Spa

Chapter 10 BridgeMES-2110 User’s Guide76On each bridge, the root port is the port through which this bridge communicates with the root. It is the port

Chapter 10 BridgeMES-2110 User’s Guide7710.1.3 STP Port States STP assigns five port states to eliminate frame looping. A bridge port is not allowed

Chapter 10 BridgeMES-2110 User’s Guide78The following table describes the labels in this screen. 10.3 The RSTP System Configuration ScreenYou must fi

Chapter 10 BridgeMES-2110 User’s Guide79The following table describes the labels in this screen. Table 25 Configuration > Bridge Menu > RSTP

Safety WarningsMES-2110 User’s Guide8

Chapter 10 BridgeMES-2110 User’s Guide8010.4 The Spanning Tree Port ConfigurationClick Configuration > Bridge Menu > RSTP Per Port Config to op

Chapter 10 BridgeMES-2110 User’s Guide81The following table describes the labels in this screen. Table 26 Configuration > Bridge Menu > RSTP

Chapter 10 BridgeMES-2110 User’s Guide82

MES-2110 User’s Guide83CHAPTER 11 VLAN11.1 OverviewThis chapter shows you how to configure 802.1Q tagged and port-based VLANs. A VLAN (Virtual Local

Chapter 11 VLANMES-2110 User’s Guide8411.2.1 Forwarding Tagged and Untagged Frames Each port on the Switch is capable of passing tagged or untagged f

Chapter 11 VLANMES-2110 User’s Guide8511.3 The VLAN Type ScreenUse this screen to select the VLAN type. Click Configuration > VLAN Menu > VLAN

Chapter 11 VLANMES-2110 User’s Guide86This screen is available only when you select Port-Based in the VLAN Type screen. Click Configuration > VLAN

Chapter 11 VLANMES-2110 User’s Guide8711.5 The Tag-Based VLAN ScreensUse the Tag-Based VLAN screens to configure VLAN settings.11.5.1 VLAN Stacking

Chapter 11 VLANMES-2110 User’s Guide88distinguish customer A and tag 48 to distinguish customer B at edge device 1 and then stripping those tags at ed

Chapter 11 VLANMES-2110 User’s Guide8911.5.4 VLAN Tag FormatA VLAN tag (service provider VLAN stacking or customer IEEE 802.1Q) consists of the foll

Contents OverviewMES-2110 User’s Guide9Contents OverviewIntroduction and Hardware ...

Chapter 11 VLANMES-2110 User’s Guide90Configure the fields as highlighted in the Switch VLAN Stacking screen. 11.5.6 The VLAN Stacking Configuration

Chapter 11 VLANMES-2110 User’s Guide91The following table describes the labels in this screen. 11.5.7 The Tag-Based Port Information ScreenUse this

Chapter 11 VLANMES-2110 User’s Guide92Click Configuration > VLAN Menu > Tag-Based > Port Info. to open the following screen.Figure 42 Confi

Chapter 11 VLANMES-2110 User’s Guide9311.5.8 The Tag-Based Port Configuration ScreenUse this screen to configure the VLAN group settings for each po

Chapter 11 VLANMES-2110 User’s Guide9411.5.9 The Management VLAN ScreenUse this to configure the management VLAN. A port must belong to the managemen

MES-2110 User’s Guide95CHAPTER 12 Bandwidth Control12.1 Overview Bandwidth control means defining a maximum allowable bandwidth for incoming and/or

Chapter 12 Bandwidth ControlMES-2110 User’s Guide96The following table describes the related labels in this screen. Table 37 Configuration > Band

MES-2110 User’s Guide97CHAPTER 13 Broadcast Storm Control13.1 OverviewThis chapter introduces and shows you how to configure the broadcast storm con

Chapter 13 Broadcast Storm ControlMES-2110 User’s Guide98The following table describes the labels in this screen. Table 38 Configuration > Storm

MES-2110 User’s Guide99CHAPTER 14 Port Mirroring14.1 OverviewThis chapter discusses port mirroring setup screens.14.2 Port Mirroring Setup Port mir