ZyXEL Communications VES-1012 - Guia do Utilizador Página 173
- Página / 227
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
VES-1000 Series Ethernet Switch
System Maintenance 2 22-5
Table 22-4 Menu 24.11.1.1 - Secured Client Configuration
FIELD DESCRIPTION EXAMPLE
Active Press [SPACE BAR] once to select Yes and then press [ENTER] to make this
client set active. This displays as “A” in menu 24.1.1.
Yes
Secured IP
addr start To allow a range of computers to use Telnet, FTP or ICMP services then enter
the first IP address in the range here.
The default value for a start and end address is 0.0.0.0, which means you don’t
care which host is trying to use a service (Telnet, FTP, or ICMP).
If you enter an IP address in this field, the VES will check if the client IP address
matches the value here when a (Telnet, FTP, or ICMP) session is up. If it does
not match, the VES will disconnect the session immediately. If the service field is
disabled in menu 24.11, then this field and the next field are N/A.
0.0.0.0
addr end To allow a range of computers to use Telnet, FTP or ICMP services, enter the
end IP address in the range here. To allow a single computer to use Telnet, FTP
or ICMP services, enter the same IP address here as in the previous field.
0.0.0.0
Service Type
TELNET
Service
Press [SPACE BAR] to select Yes or No and then press [ENTER] to
activate/deactivate this service for the trusted computers specified above.
Yes
FTP Service Press [SPACE BAR] to select Yes or No and then press [ENTER] to
activate/deactivate this service for the trusted computers specified above.
Yes
Web Service Press [SPACE BAR] to select Yes or No and then press [ENTER] to
activate/deactivate this service for the trusted computers specified above.
Yes
ICMP Service Press [SPACE BAR] once to select Yes or No and then press [ENTER] to
activate/deactivate this service for the trusted computers specified above.
Yes
Once you have filled in this menu, press [ENTER] at the message "Press ENTER to Confirm or ESC to Cancel" to
save your configuration, or press [ESC] to cancel.
22.4 Hardware Monitor
Enter 12 from Menu 24 – System Maintenance to go to the next menu shown.
- VES-1000 Series 1
- Copyright 2
- FCC Interference Statement: 3
- FCC Warning! 3
- CE Mark Warning: 3
- Certifications 3
- ZyXEL Limited Warranty 4
- Customer Support 5
- Table of Contents 6
- List of Figures 10
- List of Figures xi 11
- List of Figures xiii 13
- List of Tables 14
- List of Tables xv 15
- Preface 17
- Part I: 19
- Chapter 1 21
- Getting to Know Your VES 21
- SNMP V1 (RFC 1157) 22
- Bridge MIB (RFC-1493) 22
- 1.3 Applications 23
- 1.3.2 Enterprise Application 24
- 1.3.3 Campus Application 25
- Chapter 2 27
- Hardware Connections 27
- 2.3 Front Panel 28
- 2.4 Front Panel Ports 28
- 2.4.1 Console Port 29
- 2.4.2 VDSL Port Connections 29
- 2.5 Front Panel LEDs 30
- Part II: 31
- Chapter 3 33
- 3.3 Home Screen 34
- 3.4 Screen Overview 35
- Chapter 4 39
- Initial Configuration 39
- 8. Click the Apply button 40
- Chapter 5 41
- Getting Started Screens 41
- 5.3 IGMP Snooping 42
- 5.4.2 How STP Works 43
- 5.5 GARP Timer 44
- 5.6 Switch Setup Screen 44
- Getting Started Screens 5-5 45
- Figure 5-3 Switch Setup 45
- DESCRIPTION 46
- Getting Started Screens 5-7 47
- Table 5-4 Switch Setup 47
- 5.7 IP Setup Screen 48
- Chapter 6 51
- 6.4 Rate Adaption 52
- 6.5 VDSL Default Values 52
- 6.6 GVRP 52
- 6.7 Port Setup Screen 53
- Port Setup 6-5 55
- 6-6 Port Setup 56
- Port Setup 6-7 57
- 6-8 Port Setup 58
- Figure 6-3 Uplink Port Setup 58
- Port Setup 6-9 59
- Table 6-5 Uplink Port Setup 59
- 6-10 Port Setup 60
- Chapter 7 61
- Static Route 61
- Static Route 7-3 63
- Table 7-2 Static Route Edit 63
- Chapter 8 65
- 8.5 VLAN Setup 67
- Part III: 73
- Chapter 9 75
- 9.1.1 Supported MIBs 76
- 9.1.2 SNMP Traps 76
- 9.1.3 Configuring SNMP 76
- Chapter 10 79
- Chapter 11 81
- LABEL DESCRIPTION 82
- Maintenance 11-3 83
- Table 11-1 Maintenance 83
- Chapter 12 89
- Statistics 89
- Statistics 12-3 91
- Table 12-2 Show STP Status 91
- Statistics 12-5 93
- Table 12-3 Hardware Monitor 93
- 12.2.5 Port Details Screen 96
- 12-10 Statistics 98
- Table 12-6 Port Details 98
- Statistics 12-11 99
- Chapter 13 101
- Diagnostic 101
- 13.4 Logout Screen 103
- Part IV: 105
- Chapter 14 107
- Introducing the SMT 107
- 14.5 SMT Menus At A Glance 108
- 14.5.1 Main Menu 109
- 14.6.1 Resetting the VES 111
- Chapter 15 113
- General, Switch and IP Setup 113
- 15.2.2 GARP Timer Setup 116
- 15.3 TCP/IP Setup 118
- Chapter 16 121
- Port Setup 121
- FIELD DESCRIPTION EXAMPLE 122
- JoeSoap 122
- 16.1.3 Ethernet Port Setup 123
- 16.2 Port Submenus 125
- Part V: 129
- Chapter 17 131
- Static Route Setup 131
- 17-2 Static Route Setup 132
- Chapter 18 133
- VLAN Setup 133
- 18.3 Port-Based VLAN Setup 135
- SYMBOL DESCRIPTION 136
- Chapter 19 137
- SNMP Configuration 137
- 19.2 Supported MIBs 138
- 19.3 Configuring SNMP 138
- 19.4 SNMP Traps 139
- 19-4 SNMP Configuration 140
- Table 19-3 SNMP Traps 140
- Part VI: 141
- Chapter 20 143
- System Maintenance 1 143
- 20.2.1 System Maintenance 144
- Port Statistics 145
- 20-4 System Maintenance 1 146
- Table 20-2 Port Statistics 146
- System Maintenance 1 20-5 147
- 20.2.3 VLAN Status 149
- 20.3.1 System Information 150
- 20.4 Log and Trace 151
- 20.4.1 Viewing Error Log 152
- 20.4.2 UNIX Syslog 152
- 20.5 Diagnostic 153
- Chapter 21 155
- Maintenance 155
- 21.2 Backup Configuration 156
- 21.2.4 GUI-based FTP Clients 157
- 21.2.7 TFTP Command Example 158
- 21.3 Restore Configuration 160
- 21.3.2 FTP Restore Example 161
- 21.4.1 Firmware File Upload 162
- 21.4.5 TFTP File Upload 164
- HyperTerminal 167
- Chapter 22 169
- System Maintenance 2 169
- 22.2.1 Resetting The Time 170
- 22.3.1 Secured Client Sets 171
- 22.4 Hardware Monitor 173
- Part VII: 177
- Chapter 23 179
- VDSL-Related Commands 179
- 23.2 VDSL Commands 180
- 23.2.1 Set VDSL Mode 181
- 23.2.4 Reset a VDSL Channel 182
- VDSL-Related Commands 23-5 183
- 23.2.7 VDSL Version Command 184
- 23.2.9 VDSL Show Command 184
- 23.2.11 VDSL Debug Command 185
- 23.3.4 Enet Fctrl Command 189
- 23.3.5 Enet Monitor Command 189
- Chapter 24 191
- Switch-Related Commands 191
- 24.3 Port Status Command 192
- 24.4 VLANs 193
- 24.4.1 VLAN Status Command 194
- 24.4.2 VLAN Set Command 195
- Sw vlan set 3 1 196
- Sw vlan set 4 1 196
- 24.4.3 VLAN Clear Command 198
- Sw vlan clear all 199
- 24.5 MAC Address Commands 200
- 24.6 MAC Address Learning 201
- 24.6.2 MAC Number 202
- 24.8 Switch Driver Commands 204
- TxFreeCnt = 79287 205
- Chapter 25 207
- IP Commands 207
- 25.1.2 IGMP Snooping Queries 208
- 25.1.3 Enable IGMP Snooping 209
- Chapter 26 211
- Troubleshooting 211
- 26.4 Data Rate 212
- 26.5 Configured Settings 212
- 26.6 Password 212
- 26.7 Remote Server 213
- 26.8 Telnet 213
- 26-4 Troubleshooting 214
- Part VIII: 215
- Appendix A 217
- Product Specifications 217
- Appendix B 219
- Pin Assignments 219
- B-2 Pin Assignments 220
- B-4 Pin Assignments 222
Manuais e produtos relacionados com Redes ZyXEL Communications VES-1012 -
Redes ZyXEL Communications DI-106 Manual do Utilizador
(168 páginas)
(168 páginas)
Redes ZyXEL Communications VSG1432 Guia do Utilizador
(408 páginas)
(408 páginas)
Redes ZyXEL Communications G-3000 Guia do Utilizador
(19 páginas)
(19 páginas)
Redes ZyXEL Communications G-102 Guia do Utilizador
(198 páginas)
(198 páginas)
Redes ZyXEL Communications ES-305 Guia do Utilizador
(118 páginas)
(118 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais